GNU bug report logs - #79288
[PATCH] Add edebug-bounce-to-previous-value

Previous Next

Full log

View this message in rfc822 format

From: Jens Schmidt <jschmidt4gnu <at> vodafonemail.de>
To: Eli Zaretskii <eliz <at> gnu.org>
Cc: 79288 <at> debbugs.gnu.org, monnier <at> iro.umontreal.ca
Subject: bug#79288: [PATCH] Add edebug-bounce-to-previous-value
Date: Sun, 24 Aug 2025 15:42:40 +0200

On 2025-08-24  14:31, Eli Zaretskii wrote:
>> Date: Sun, 24 Aug 2025 14:02:52 +0200
>> Cc: 79288 <at> debbugs.gnu.org, monnier <at> iro.umontreal.ca
>> From: Jens Schmidt <jschmidt4gnu <at> vodafonemail.de>
>>
>> On 2025-08-24  13:58, Eli Zaretskii wrote:
>>
>>> Hmm... either I'm blind, or there's no note in NEWS about removing the
>>> previous key binding of 'P'.
>>
>> Sorry, forgot to format-patch.  Next attempt ...
> 
> OK, last nit:
> 
>> --- a/doc/lispref/edebug.texi
>> +++ b/doc/lispref/edebug.texi
>> @@ -677,8 +677,7 @@ Edebug Views
>>  
>>  @table @kbd
>>  @findex edebug-view-outside
>> -@item P
>> -@itemx v
>> +@item v
>>  Switch to viewing the outside window configuration
>>  (@code{edebug-view-outside}).  Type @kbd{C-x X w} to return to Edebug.
> 
> This section, like many others, start with a summary of the commands,
> followed by the detailed description.  You added the detailed
> description, but please also add this new command to the summary part.

In section "Edebug Views" the patch has three hunks: The short one you
quoted above, then this one, which I considered to be the "summary part":


  @@ -689,6 +688,17 @@ Edebug Views
   before returning to Edebug.  With a prefix argument @var{n}, pause for
   @var{n} seconds instead.

  +@findex edebug-bounce-to-previous-value
  +@item P
  +Temporarily display the outside current buffer with the outside point
  +corresponding to the previous value
  +(@code{edebug-bounce-to-previous-value}).  The previous value is what
  +Edebug has evaluated before its last stop point or what you have
  +evaluated in the context outside of Edebug, for example, with
  +@kbd{C-x C-e}.  This command pauses for one second before returning to
  +Edebug.  With a prefix argument @var{n}, it pauses for @var{n} seconds
  +instead.
  +
   @findex edebug-where
   @item w
   Move point back to the current stop point in the source code buffer


And finally the third hunk, supposed to be the example/detailed
description:

  @@ -713,6 +723,20 @@ Edebug Views
   bounce to the point in the current buffer with @kbd{p}, even if
   it is not normally displayed.

  +  You can also bounce to buffer positions other than the current point.
  +Suppose you are debugging the form
  +
  +@example
  +(make-overlay beg end)
  +@end example
  +
  +@noindent
  +and you would like to know where @code{beg} and @code{end} are located
  +in the outside buffer.  Then you could either evaluate these, for
  +example, with @kbd{C-x C-e}, or step over them with @kbd{n}, and
  +immediately after that press @kbd{P}, to bounce to the position you have
  +previously evaluated.
  +
     After moving point, you may wish to jump back to the stop point.
   You can do that with @kbd{w} from a source code buffer.  You can jump
   back to the stop point in the source code buffer from any buffer using


Wouldn't that be sufficient?  If not, where exactly in the section would
you expect the "summary part"?

Thanks!

Previous Next

GNU bug tracking system
Copyright (C) 1999 Darren O. Benham, 1997,2003 nCipher Corporation Ltd, 1994-97 Ian Jackson.